|
|
|
|
|
- Pack of five blanking plates
- Dimensions: 15 x 16mm
- Colour: White
- Warranty: 2 years
|
|
|
|
This cable tester is a compact, palm sized unit for testing USB and network cables. It can be used to read and check the pin-out configuration of cables before and after installation. A separate passive module is included for remote testing of pre-installed cables.
- Auto/manual scan modes
- Separate status LED for each wire
- Tests the following cables: USB (Type A/A, Type A/B), RJ-45 (UTP/STP), BNC, Co-axial and RJ-11/RJ-12 modular cables
- Supports the following standards: EIA/TIA 568A/568B, AT&T 258A, ISDN, 10Base-2, 10Base-T, 100Base-TX, 1000Base-T, Token Ring
- Carry case included
- Requires 9V PP3 battery (Part No. 84844)
- Dimensions: 65 x 137 x 30mm (WxHxD)
|
|
|
|
The LINDY Modular AV Face Plate System allows you to create your own custom face plates by using a combination of Snap-in Blocks and Keystone modules. Fit this LC Duplex Multimode Keystone into a Keystone Snap-in Block and place into a face plate along side other Keystone and Snap-in modules.
These modules provide a full range of solutions for AV, networking, voice and audio installations. The wide selection of modules and face plates can be custom configured giving you greater control and flexibility.
- LC Fibre Duplex Multimode Female connectors
- Allows LC Fibre cables to be connected to a face plate
- Suitable for use with our range of snap in bezels and wall plates
- 2 year warranty
Please scroll down for more information about installing this product...
|
|
Media Converters / Transceivers
|
|
|
This Fast Ethernet Fibre Optic Converter allows you to convert and extend your Fast Ethernet network by up to 2km using fibre optic cable. The fibre optic signal is totally immune to electromagnetic and radio frequency interference, and is electrically isolated. The ideal solution for high speed interconnections up to 200Mbps (Full-duplex) between buildings and floors.
- 100Base-FX (fibre) to 10/100Base-TX (copper)
- Standards: IEEE 802.3, 802.3u, 802.3x
- Connectors: LC (fibre), RJ-45 (copper)
- Maximum fibre cable distance - 2km
- Network data transfer rate: 200Mbps (Full-duplex)
- Auto MDI-X support for RJ-45 port connection
- Status LED for Speed, Link/Activity, Full-duplex, Power
- External power supply 5V DC, 2A
- Dimensions: 74 x 102 x 22mm (WxDxH)
Due to the specialist nature of single mode fibre cable, please contact us to discuss your requirements
|
|
|
|
This Gigabit Ethernet Fibre Optic Converter allows you to convert and extend your Gigabit Ethernet network by up to 550m using fibre optic cable. The fibre optic signal is totally immune to electromagnetic and radio frequency interference, and is electrically isolated. The ideal solution for high speed interconnections up to 200Mbps (Full-duplex) between buildings and floors.
- 1000Base-T (copper) to 1000Base-LX (fibre)
- Standards: IEEE 802.3, 802.3u, 802.3x
- Connectors: LC (fibre), RJ-45 (copper)
- Maximum fibre cable distance - 550m using 50/125µm multi-mode cable, 220m using 62.5/125µm multi-mode cable
- Network data transfer rate: 200Mbps (Full-duplex)
- Auto MDI-X support for RJ-45 port connection
- Status LED for Speed, Link/Activity, Full-duplex, Power
- External power supply 5V DC, 2A
- Dimensions: 74 x 102 x 22mm (WxDxH)
Due to the specialist nature of single mode fibre cable, please contact us to discuss your requirements
|
|
First <-- Previous Next --> Last
Useful Links
Profigold Cables
Ixos Cables
HDMI Cable
Thor Cables
We Also Accept
|
|
|
Designed & Maintained by Nimbus Designs Ltd
|
Nimbus Designs Ltd - Trading as TVCables
Registered in England No 1521727
Registered Office - Shefford Busniness Centre, 71 Hitchin Road, Shefford, Beds, SG17 5JB - Tel 0207 100 4874
Parcels and Visitors are NOT accepted at this address.
© Copyright 2015 TVcables All rights reserved.
|
|
|